Ransburg RMA202 Test Stand 77918-08 User Manual

IMPORTANT: Before using this equipment, carefully read SAFETY PRECAUTIONS, starting on page 1, and all instructions in this manual. Keep this Servic

Power Control - On/Off ButtonMain Gauges - Leak Down, Supply AirAir Flow Meter - Turbine Air, Shape Air, Seal AirAir Flow Meter - Bearing AirFiber Opt

SETUP PROCEDURE1. Insure that ground connections, cart ground, and applicator ground are made to a true earth ground.INSTALLATION2. Provide air l

2. With control panel power Off, cover the end of the applicator with a plastic bag to contain the electrostatic voltage and prevent current fr

N O T E> The HV is interlocked electrically with the trigger switches. When a uid switch is triggered on, the HV will automatically be turned of

Figure 11: P#1 & P#2 Trigger SwitchesFigure 12: Pressure Test BellN O T E> For this part of the test, the spin guard should be in the down po

Figure 13: Bell Solvent SwitchN O T E > For signal line verication consult the most current RMA-202 applicator service manual. Pull valves out

7. Manually turn up the water pressure to 70 psig (read on the front panel) by adjusting the pres- sure regulator on the pressure pot. Verify by

Bearing Air TestThis test is to verify the applicator responds to changes in set points in the speed selector. The procedure to accomplish this is:1.

8. On the atomizer speed select card, toggle the “Enable” #1 switch down.9. Stop the spinning bell by pressing the manual brake button on the fr

in size as air pressure for the shaping air is adjusted.6. Turn off the trigger for Paint #2. Trigger the solvent line and repeat the adjustment

1-5SAFETY:PAGESAFETY PRECAUTIONS...HAZARDS

C A U T I O N!> Do not depress the manual brake button if turbine speed is zero. This will cause the turbine shaft to rotate in reverse. This wi

MAINTENANCEThere should be no maintenance required. If any maintenance is required, consult factory for spare part availability.RMA-202 Test Stand -

WARRANTY POLICIESLIMITED WARRANTYRansburg will replace or repair without charge any part and/or equipment that fails within the specied time (see bel

PAINT AND SOLVENT SPECIFICATIONSAEROBELL® II*** AEROBELL®AEROBELL® 33 RMATM-10118 TO 30 SEC.1 MW TO ¥1000 cc/minTURBODISKTMNO. 2 HAND GUNREMTM / M90T

VISCOSITY CONVERSION CHART.1.15.2.25.3.4.5.6.7.8.91.01.21.41.61.82.02.22.42.62.83.03.23.43.63.84.04.24.44.64.85.05.56.07.08.09.010.011.012.01015202530

VISCOSITY CONVERSION CHART (Continued)13.014.015.016.017.018.019.020.021.022.023.024.025.030.035.040.045.050.055.060.065.070.075.080.085.090.095.0100

3.65.66.88.810.224.636.360.810.224.636.360.815.3 cc36.9 cc54.5 cc91.2 cc30.5 cc73.9 cc109.0 cc182.5 cc45.8 cc110.8 cc163.4 cc273.7 cc61.1 cc147.8 cc21

Service Manual Price: $30.00 (U.S.)Form No. LN-9527-00.1Litho in U.S.A.03/13© 2013 Ransburg. All rights reserved.Models and specications subject to

W A R N I N G!W A R N I N G!SAFETYSAFETY PRECAUTIONSBefore operating, maintaining or servicing any Ransburg electrostatic coating system, read and u

Spray AreaAREATells where hazards may occur.HAZARDTells what the hazard is.SAFEGUARDSTells how to avoid the hazard.Fire HazardImproper or inadequate o

AREATells where hazards may occur.HAZARDTells what the hazard is.SAFEGUARDSTells how to avoid the hazard.Spray AreaImproper operation or mainte-nance

AREATells where hazards may occur.HAZARDTells what the hazard is.SAFEGUARDSTells how to avoid the hazard.Spray Area / High Voltage EquipmentElectrical

Toxic SubstancesCertain material may be harmful if inhaled, or if there is contact with the skin.Follow the requirements of the Material Safety Data S

INTRODUCTIONGENERAL INFORMATIONThe Ransburg Applicator Performance Test Stand was developed to assist in determining the applicator level of performa

Main Control PanelAir Flow MetersTest ApplicatorTablePressure PotDump BucketSpin GuardMain Air Regulator12345678Item #DescriptionBASIC STAND FEATURES