Ransburg Discrete IO Module A11435 User Manual

SERVICE MANUALLN-9253-06.1(Replaces LN-9253-06)April - 2013 MODEL: A11435IMPORTANT: Before using this equipment, care-fully read SAFETY PRECAUTIONS,

SPECIFICATIONSEnvironmental/PhysicalOperating Temperature: 0°C to 55°CStorage Temperature: -40°C to 85°C Humidity: 0 to 95% non- condensin

INSTALLATIONCONNECTIONSSee "Connections from Computer Serial Port to Discrete I/O RJ12 Terminal Connector" in the "Maintenance" se

Analog Inputs0-10 VDC or 4-20 mA set by position 8 of SW2. In 0 to 10 VDC mode (SW2-8 down), input impedance is 150 kohm. In 4 to 20 mA mode (SW2-8

Digital Inputs24 VDC source (SW7, 8 Up) or sink SW7, 8 Down)Ground Reference 18A, 14A, or 13A.High Voltage On - If High Voltage Ready is active, cause

Discrete Outputs(Contact ratings: 2 A @ 28 VDC resistive, 0.5 A @ 120 VAC resistive, one side common with 30C)High Voltage On - Indicates High Voltag

Figure 1: Required Dipswitch SettingsREQUIRED DIPSWITCH SETTINGSDiscrete I/O Module - Safety12LN-9253-06.1Ransburg

Figure 2: Required Slide Switch SettingsDiscrete I/O Module - Safety13LN-9253-06.1Ransburg

MAINTENANCETROUBLESHOOTINGNormal Operation(Normal for 3 seconds on Power Up.) Discrete I/O module not communicating on Serial bus with MicroPak or Se

Starting and Conguring HyperTerminal Software1. Start the HyperTerminal software (START/ACCESSORIES/COMMUNICATION/HYPER-TERMINAL). 2. The software

WARRANTY POLICIESLIMITED WARRANTYRansburg will replace or repair without charge any part and/or equipment that falls within the specied time (see bel

Discrete I/O ModuleLN-9253-06.1Ransburg

PAINT AND SOLVENT SPECIFICATIONSAEROBELL® II*** AEROBELL®AEROBELL® 33 RMA-101TM18 TO 30 SEC.1 MW TO ∞1000 cc/minTURBODISKTMNO. 2 HAND GUNREMTM / M90T

VISCOSITY CONVERSION CHARTPoise.1.15.2.25.3.4.5.6.7.8.91.01.21.41.61.82.02.22.42.62.83.03.23.43.63.84.04.24.44.64.85.05.56.07.08.09.010.011.012.0Centi

VISCOSITY CONVERSION CHART (Continued)Poise13.014.015.016.017.018.019.020.021.022.023.024.025.030.035.040.045.050.055.060.065.070.075.080.085.090.095.

LengthVOLUMETRIC CONTENT OF HOSE OR TUBE(English Units)I.D. (inches)5ft. (60") 1/83/161/45/163/81/22.45.49.715.121.738.6.012.028.049.077.110.19

Discrete I/O Module - Safety21LN-9253-06.1Ransburg

Service Manual Price: $30.00 (U.S.)Form No. LN-9253-06.104/13© 2013 Ransburg. All rights reserved.Models and specications subject to change without

MAINTENANCE:SAFETY:SAFETY PRECAUTIONS...HAZARD

W A R N I N G!W A R N I N G!SAFETYSAFETY PRECAUTIONSBefore operating, maintaining or servicing any Ransburg electrostatic coating system, read and u

Spray AreaAREATells where hazards may occur.HAZARDTells what the hazard is.SAFEGUARDSTells how to avoid the hazard.Fire HazardImproper or inadequate o

AREATells where hazards may occur.HAZARDTells what the hazard is.SAFEGUARDSTells how to avoid the hazard.Spray AreaImproper operation or mainte-nance

AREATells where hazards may occur.HAZARDTells what the hazard is.SAFEGUARDSTells how to avoid the hazard.Spray Area / High Voltage EquipmentElectrical

Toxic SubstancesCertain material may be harmful if inhaled, or if there is contact with the skin.Follow the requirements of the Material Safety Data S

INTRODUCTIONGENERAL DESCRIPTIONThe Discrete I/O Module II is used as a bridge between analog and digital control signals and the MicroPak High Voltag