Ransburg 22-1589 Service Manual

SERVICE MANUALLN-9405-00.1Replaces (LN-9405-00)SERVO AMPLIFIERMODEL: 22-1589IMPORTANT: Before using this equipment, carefully read SAFETY PRECAUTION

LN-9405-00.1Servo Amplier - Installation7PROGRAM MODESOperation With A Pulse SourceComplete a motor, power, and I/O wiring to the terminal block. Wh

LN-9405-00.1Servo Amplier - Installation8Figure 3: Default Pulse Mode Programmable Parameters TablePLAVI1VI4VF10VF11VF12VF13VF14VF15VF16VF18VF19Sets

LN-9405-00.1Servo Amplier - Installation9• Select desired PLA to correspond to the re-quired gear ratio.• Type SAVE, the controller wil respond, “Sav

LN-9405-00.1Servo Amplier - Installation10RETROFIT KIT (78694), RCS AMPLIFIER RETROFITRetrot Kit DescriptionThis Retrot Kit enables the end user to

LN-9405-00.1Servo Amplier - Installation1114151617181920212223242526S2K RETROFIT KIT TRANSITION BOARD TERMINAL DESCRIPTIONS (Cont.)S2K RetrotTermina

LN-9405-00.1Servo Amplier - Installation12Reference the S2K Retrot Kit Transition Board Terminal Description for the signal description of the ter

LN-9405-00.1Servo Amplier - Installation13RETROFIT KIT (78694-02) PULSE MODE OPERATIONThis kit is used in RCS Systems that utilize the Motor Control

LN-9405-00.1Servo Amplier - Installation14RETROFIT KIT (78694-01) ANALOG MODE OPERATIONThis kit is used in RCS Systems that use the UL Listed and non

LN-9405-00.1Servo Amplier - Installation15GE FANUC S2K AMPLIFIER TERMINATIONS2K Auxilary I/O Cable DescriptionThe following Tables depict the termina

LN-9405-00.1Servo Amplier - Installation16Figure 10: S2K Position Feedback Cable TableMtr. ResolverMtr. ResolverMtr. ResolverMtr. ResolverMtr. Resol

LN-9405-00.1

LN-9405-00.1TROUBLESHOOTING GUIDEServo Amplier - Troubleshooting Guide17Figure 12: Diagnostic Faults TableOKFaultedFaultedFaultedFaultedFaultedFault

LN-9405-00.118Servo Amplier - Parts IdenticationPARTS IDENTIFICATIONPART #DESCRIPTION22-158978694-0078694-0178694-02AmplierRetrot KitAnalog Mode -

LN-9405-00.1WARRANTY POLICIESLIMITED WARRANTYRansburg will replace or repair without charge any part and/or equipment that falls within the specied t

LN-9405-00.1 Servo Amplier - Appendix20PAINT AND SOLVENT SPECIFICATIONSAEROBELL® II*** AEROBELL®AEROBELL® 33 RMATM-10118 TO 30 SEC.1 MΩ TO ∞1000

LN-9405-00.1Poise.1.15.2.25.3.4.5.6.7.8.91.01.21.41.61.82.02.22.42.62.83.03.23.43.63.84.04.24.44.64.85.05.56.07.08.09.010.011.012.01015202530405060708

LN-9405-00.1Poise13.014.015.016.017.018.019.020.021.022.023.024.025.030.035.040.045.050.055.060.065.070.075.080.085.090.095.0100.0110.0120.0130.0140.0

LN-9405-00.1 23Servo Amplier - AppendixLengthVOLUMETRIC CONTENT OF HOSE OR TUBE(English Units)I.D. (inch-es)5ft. (60”) 1/83/161/45/163/81/22.4

Form No. LN-9405-00.1Litho in U.S.A.04/13Service Manual Price: $20.00 (U.S.)© 2013 Ransburg. All rights reserved.Models and specications subject to

LN-9405-00.1CONTENTSSAFETY:SAFETY PRECAUTIONS...

LN-9405-00.1SAFETYServo Amplier - Safety1> The user MUST read and be familiar with the Safety Section in this manual and the Ransburg safety lite

LN-9405-00.1Servo Amplier - Safety2AREATells where hazards may occur.HAZARDTells what the hazard is.SAFEGUARDSTells how to avoid the hazard.Spray Are

LN-9405-00.1Servo Amplier - Safety3AREATells where hazards may occur.HAZARDTells what the hazard is.SAFEGUARDSTells how to avoid the hazard.Electrica

LN-9405-00.1Servo Amplier - Introduction4INTRODUCTION(For a General Description, Features, and Specications, Reference GE Fanuc S2K Series Standalon

LN-9405-00.1Servo Amplier - Introduction5CONNECT AND CONFIGURE AMPLIFIERAmplier Termination• Complete the motor, power, and I/O wiring to the S2K Am

LN-9405-00.1Servo Amplier - Installation6INSTALLATIONSETUP AND OPERATIONSummary of Dip Switch Functions(Refer to the S2K Hardware Manual for an expla